EK Ballast Install

[eks]

Thanks! You diags are sweet! They are much more professional then what I have done with MS Paint. Thanks!

Let me know if there is any diagram you want me to work on...

Nothing like having the right tool!

[chpthril]

chpthril,

Sorry for taking so long to answer it, I've being hibernating with my boat over the cold winter.

I used Visio to create thoso drawings.

Do you need a new drawing?

Thanks! You diags are sweet! They are much more professional then what I have done with MS Paint. Thanks!

[eks]

chpthril,

Sorry for taking so long to answer it, I've being hibernating with my boat over the cold winter.

I used Visio to create thoso drawings.

Do you need a new drawing?

Hey, what are you guys using to create these diagrams? Thanks

[chpthril]

Thanks guys, I got Sketchup downloaded and installed, but havent tried it out yet.

[dogbert]

x2 on Google Sketchup!

[SPBFAN]

Hey, what are you guys using to create these diagrams? Thanks

I use Google Sketch up. It works good. I think they are using the same things but not sure. http://sketchup.google.com/

[chpthril]

Hey, what are you guys using to create these diagrams? Thanks

[xpjim1]

I can tell you the Home Depot hose is larger than it says. Especially the all white hose. I bought the 1.5 inch inside diameter there and it was larger than the barb and would not tighten down. Went to west marine and bought 1.5 inch white hose and had to use the heat gun to get it over the barb. Difference mightbe the hose at home depot says spa hose and west marine it is bilge hose

[SPBFAN]

Nice wave EKS. And that looks like it is mud lake. Just wait until you get to a lake that actually has some depth to it and the hull of the boat can go to work. You will be very happy with the wave.

[KonaKing]

Here is the wake I got with just me and my wife on the boat. Taps at 4 and speed set to 10.8 mph

This picture was taken from my Cell phone, next time I'll take a regular camera.

I'll surf it

[dogbert]

The ballast puppy pumps are a little smaller than 1" and the hose fit in a little loose. Since the hose is so hard no matter what I did I still got water leaking out.

I bought the white hose at home Depot and they did tell me they will take back some of the white hose and replace with a more flexible one.

That's where I got my hose. I bought the clear plastic with the wire mesh in it. It works really well, except for the last 4-5' on the roll where it got flattened. It's a PITA to get that round again. But, it won't collapse under pressure.

[TigeDuner]

I found those same check valves at a local pluming supply. I need to trade some of the very hard white hose for a more flexible one. The only leak I had was because the clamp could not clamp enough the hardness of the hose. I need to replace that connection.

The outside temp was perfect 72 degree, but the water temp was about 63 degrees... Still a little nippy for me without a thick web suit or dry suit.

I am planning to get in the water for the first time this next weekend to make sure all is working before a little trip to Powell next week.

Saturday the air temp was 68 and the water was 69. No wet suits, just sweatshirts when we got out. Water and air warmed up on Sunday and Monday-then it was crowded. We were on the water about 8:00 on Monday for a round of glass for each of us.

Let me know if you want to use some of the hose that I used. A 50' roll is 63.00 delivered and I only need about 10 feet. We could split a roll if you want to use this hose. Shipping to you would be another 7.00 so 35.00 for 25'. Very flexible and easy to push on. Let me know. TD

[eks]

Try a little plumbers putty first. You may be able to seal it enough to make what you have work.

The ballast puppy pumps are a little smaller than 1" and the hose fit in a little loose. Since the hose is so hard no matter what I did I still got water leaking out.

I bought the white hose at home Depot and they did tell me they will take back some of the white hose and replace with a more flexible one.

[dogbert]

I found those same check valves at a local pluming supply. I need to trade some of the very hard white hose for a more flexible one. The only leak I had was because the clamp could not clamp enough the hardness of the hose. I need to replace that connection.

Try a little plumbers putty first. You may be able to seal it enough to make what you have work.

[eks]

I found those same check valves at a local pluming supply. I need to trade some of the very hard white hose for a more flexible one. The only leak I had was because the clamp could not clamp enough the hardness of the hose. I need to replace that connection.

The outside temp was perfect 72 degree, but the water temp was about 63 degrees... Still a little nippy for me without a thick web suit or dry suit.

I am planning to get in the water for the first time this next weekend to make sure all is working before a little trip to Powell next week.